As a tabletop water fountain supplier, I’ve spent years working with hundreds of customers – from small home decor businesses to busy office managers – and one of the most common questions I get isn’t about choosing a fountain size or pick – it’s about storing it properly when it’s not in use. I’ve seen too many nice, well-made fountains get ruined because someone skipped a step: water left sitting in the pump, mineral deposits building up inside the reservoir, or delicate ceramic parts cracked from cold storage. Storing a tabletop water fountain isn’t just about shoving it in a closet until next season – it’s a small process that protects your investment, keeps your fountain working for years, and even saves you time when you’re ready to set it back up. Tabletop Water Fountain

I know it might seem tedious, especially if your fountain is lightweight and easy to move, but trust me: I’ve seen a $150 ceramic tabletop fountain get tossed out after one bad winter because someone drained it halfway and left the pump wet inside. It only takes about 15 extra minutes of work, and it’s way better than replacing a fountain every couple of years. Let’s break this down step by step, so you can do it right, no matter what kind of tabletop fountain you have – whether it’s the small tabletop ones for home, the mid-sized ones for reception desks, or even the glass and metal ones for boutique stores.
First, before you even touch water, make sure you’re working in the right space. I always tell customers to pick a flat, dry area that’s easy to wipe – a kitchen counter, a garage workbench, or even a big plastic tarp on the floor. You don’t want to spill water on your carpet or wooden floors, and you don’t want to trip over loose parts while you’re disassembling. Also, grab a few supplies ahead of time: clean cloths (microfiber works best because it doesn’t scratch finishes), a small bucket or tray for holding water, a soft-bristled brush (an old toothbrush works for tight spots), and a dry towel for drying everything off. If you have a fountain with wooden parts, make sure your space is well-ventilated – wood absorbs moisture, and a damp closet can warp it fast.
Now, start with the easiest step: turn off the fountain and unplug it. This is non-negotiable – even if you’re just moving it, never reach for the pump while it’s plugged in. Unplug it from the wall (or the power strip, if it’s hardwired for a commercial space) first. Then, carefully lift the fountain’s top tier – the part where the water flows over – and set it aside on your towel. Be gentle here, especially if your fountain is made of cast stone, glass, or thin ceramic; those can chip or crack if you set them down too hard. Under that top tier, you’ll usually find the reservoir – the base that holds the water – and the pump sitting inside.
Next, drain the water completely. Don’t just tip the fountain a little – lift the reservoir’s edge and pour all the water out into your bucket. I always recommend doing this slowly, because sometimes small debris like dust or leaves can settle at the bottom, and you don’t want that splashing all over your clothes. If your fountain has a small hose connecting the pump to the top tier, you can also disconnect that now – just make sure you don’t kink it, because kinks can lead to blockages when you reuse it.
Once the water is out, it’s time to clean – not just rinse, but deep clean. Mineral deposits are the biggest enemy here, especially if you use hard tap water. I get so many messages from customers saying their fountain had white crusty spots all over it after a few months – that’s minerals from the water, and if you don’t clean them before storing, they’ll etch into the finish permanently. For the reservoir and the top tier, mix a mild solution: a cup of warm water and a tablespoon of white vinegar. Vinegar is perfect because it breaks down mineral deposits without damaging most finishes – ceramic, glass, metal, and even plastic are all safe with vinegar. Dip your microfiber cloth in the solution, scrub every part of the reservoir, the inner walls, and the top tier, paying extra attention to the grooves where water flows. If you have tough, crusty spots, use your old toothbrush to gently scrub them away – don’t use steel wool or abrasive sponges, because they’ll scratch the surface.
Don’t forget the pump – this is the part that actually makes the fountain work, and it’s the most likely to get clogged. Take the pump out of the reservoir – you’ll usually see it sitting in a little slot, with a power cord leading out. Submerge the pump in the vinegar-water solution for about 10 minutes; this dissolves any mineral buildup inside the impeller, the little wheel that moves water. After 10 minutes, use your soft brush to gently clean the pump’s intake screens and the impeller – you can turn the impeller by hand to make sure it moves freely, no grime sticking. If your pump has a filter, rinse that under warm water to remove any debris. Once the pump is clean, set it on a towel to dry completely. If you leave a wet pump in storage, moisture can cause mold or mildew, which will come back as a foul smell when you set the fountain up again – nobody wants a smelly fountain on their desk.
Now, dry every single part thoroughly. This is another step I see people skip all the time. Even a tiny bit of water left in the reservoir or pump can lead to mold, mildew, or even rust if your fountain has metal parts. Take your dry microfiber cloth and wipe every inch of the reservoir, the top tier, the hoses, and the pump. For the inside of the reservoir, you can even leave a dry towel folded inside for 30 minutes to absorb any leftover moisture – just make sure to pull it out before putting the fountain away. If you have a wooden base, use a wood-specific polish after drying to protect it from drying out or warping in storage; this extra step will keep it looking like new for years.
Once everything is 100% dry, it’s time to pack it properly. The biggest mistake here is putting the fountain in a tight, cold space like a garage or attic in the winter – extreme temperatures can crack ceramic, warp wood, or make glass shatter. I always recommend storing your tabletop water fountain in a cool, dry closet or storage room, away from direct sunlight (sunlight can fade finishes over time) and away from freezing temperatures. If you have the original packaging, that’s the best – it’s cut to fit your fountain, so there’s no movement that could cause chips. If you don’t have the original packaging, use soft packing materials: bubble wrap for glass or ceramic parts, old towels, or even tissue paper to wrap each part separately. Don’t stack heavy things on top of the fountain – that’s a surefire way to crack a base or bend a metal tier. If you’re storing it with the pump, wrap it in a dry cloth and put it in a small plastic bag (leave it open a little so air can circulate) to keep dust out.
Wait, what if your fountain has LED lights? A lot of our tabletop fountains have small LED lights that run off the pump – make sure you unplug the light’s connector (if there is one) and wipe that down too. Never store a fountain with the LED lights still attached while they’re wet, because moisture can short them out. If you can, take the light out and store it separately in a small box, wrapped in tissue paper, to protect it.
I also get questions from customers who use their fountains year-round, even in the cold. If you’re storing it for a short break, like a week, you don’t have to do a full deep clean – but you still need to drain all the water and dry the pump, to keep it from getting clogged with mineral buildup. For long-term storage, like a few months over winter, the deep clean is non-negotiable.
I’ve tested this process hundreds of times in our showroom, and it works every time. Last year, a customer stored our mid-sized glass reception fountain over the winter using these steps, and when she set it back up in spring, it worked perfectly – no clogs, no crusty spots, no mold. Another customer skipped the drying step, and his small ceramic fountain had a mildew smell so bad he had to replace the whole thing. It’s really that simple.
At the end of the day, your tabletop water fountain is an investment – it’s for relaxing, for adding a nice touch to your home or office, for even helping with quiet sounds that reduce stress. Taking 20 minutes to store it properly when you’re not using it means you’ll get years of use out of it, instead of replacing it every year.

If you’re a business owner looking to stock high-quality tabletop water fountains, or a retailer who wants to offer these products to your customers, we’re here to help. We provide durable, easy-to-store tabletop fountains designed with long-term use in mind, and we can work with you to find the right options for your space. Reach out to our team to learn more about our wholesale pricing and product lines.
Indoor Water Fountain References
- The Spruce. (2022). How to Clean and Store Water Features for the Winter. Retrieved from home improvement and decor resources
- Environmental Protection Agency. (2021). Mineral Buildup in Home Water Features: Prevention and Care. Retrieved from residential water care guidelines
- National Wood Flooring Association. (2020). Moisture Management for Wooden Home Decor Items in Storage. Retrieved from wood product care standards
- Consumer Product Safety Commission. (2019). Safe Storage of Electrical Small Appliances for Home Use. Retrieved from small appliance safety guidelines
Shishi Mica Craft Co., Ltd.
Shishi Mica Craft Co., Ltd. is one of the most professional tabletop water fountain manufacturers and suppliers in China, also supports high quality custom service and OEM&ODM service. Please feel free to wholesale the best tabletop water fountain made in China here from our factory. Welcome to contact us for price list and product catalog.
Address: Floor 3, No.361 Shijin Road, Jinshang Town, Shishi City, Quanzhou City, Fujian Province, China
E-mail: fanny.lv@minorca.cc
WebSite: https://www.micaltd.com/